Detecto 204 Spécifications Page 1

204WEIGHT INDICATOR INSTALLATION and TECHNICAL MANUAL 8555-M313-01 Rev G PO BOX 151 WEBB CITY, MO 64870 Printed in USA06/12 PH (417) 673-4631 - FAX

INSTALLATION, CONT. Battery Installation/Replacement To install or remove the batteries, the following steps should be followed:1. Make sure the AC p

INSTALLATION, CONT. Battery Status If batteries are used, the indicator will show the battery status on power up. The display will showbattry then ch

INSTALLATION, CONT. Main PCB and Jumpers Figure No. 5 J1 and J2 - Sense Jumpers If sense leads are NOT used, you must install plug-in jumpers at J1 an

SERIAL DATA FORMATS Weight-On-DemandIf the Printer Continuous output was not selected, COnt=0 (0=NO) during setup and calibration of the indicator, an

KEYPAD FUNCTIONS Figure No. 7 The membrane keypad is not to be operated with pointed objects (pencils, pens, fingernails, etc). Damage to keypad resu

KEYPAD FUNCTIONS, CONT. UNITS / S (UP ARROW) KEYThis key is used to change the weighing units to the alternate units of measurement if selected during

ANNUNCIATORS, CONT. lbThe lb annunciator is located on the right of the weight display and is turned on to show that the displayed weight units is p

SETUP AND CALIBRATION Your 204 indicator has been thoroughly tested and calibrated before being shipped to you. If you receive the indicator with a s

SETUP AND CALIBRATION, CONT. Decimal Point Location With the display showing dPP= press the ASTERISK key to show the current setting. Press the UNITS

SETUP AND CALIBRATION, CONT. USA (Domestic or International) The display will next indicate USA=. This is the prompt to select whether the 204 is use

8555-M313-O1 Rev G x 204 Installation & Technical 2

SETUP AND CALIBRATION, CONT. Hold Key Enable The display will next indicate HLd= which is the prompt for the selection to enable or disable the Hold (

SETUP AND CALIBRATION, CONT. Sleep Mode The display will now show SLP=. The Sleep Mode feature also conserves battery power when the indicator remain

SETUP REVIEW The 204 allows several operational parameters to be reviewed and changed as necessary without having to enter the setup and calibration m

CALIBRATION SEAL INSTALLATION If your Model 204 Weight Indicator is used in a commercial application it must be tested and sealed by your local weight

ERROR AND STATUS DISPLAYS The 204 is equipped with a diagnostic software program that tests various portions of the indicator's circuitry and ver

NOTES8555-M313-O1 Rev G x 204 Installation & Technical 23

204 PARTS IDENTIFICATION 8555-M313-O1 Rev G x 204 Installation & Technical 24

204 PARTS IDENTIFICATION ITEM PART NO. QTY DESCRIPTION1 593GR986 1 SERIAL TAG 2 6013-0039 5 NUT HEX #6-32 3 6013-0245 4 HEX NUT #4-40 4 6021-0661 6

STATEMENT OF LIMITED WARRANTY WARRANTY TERMS Cardinal Scale Manufacturing Company warrants the equipment we manufacture against defects in material an

PRODUCTTYPETERMMATERIAL ANDWORKMANSHIPLIGHTNINGDAMAGESee note 9WATERDAMAGESee note 7CORROSIONSee note 4 ON-SITE LABORLIMITATIONSANDREQUIREMENTSVEHICLE

TABLE OF CONTENTS Specifications xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx Page 1 European Declaration of Conformity xxxxxxxxxxxxxxxxxxxxxxxx Page 2Sit

APPLICABLE LIMITATIONS AND REQUIREMENTS 1. This warranty applies only to the original purchaser. The warranty does not apply to equipment that has b

A.) This warranty does not include replacement of consumable of expendable parts. The warranty does not apply to any item that has been damaged due t

8555-M313-O1 Rev G x 204 Installation & Technical 28555-M313-O1 Rev G x 204 Installation & Technical 62

FCC COMPLIANCE STATEMENT WARNING! This equipment generates uses and can radiate radio frequency and if not installed and used in accordance with the

SPECIFICATIONSPower Requirements: 115 VAC 50/60Hz 12 VDC 300mA wall plug-in UL/CSA listed AC power adapter, Cardinal part number 728R90. Also availa

EUROPEAN DECLARATION OF CONFORMITY Manufacturer: Cardinal Scale Manufacturing Company PO Box 151 203 East Daugherty Webb City, M

SITE PREPARATION REQUIREMENTS The Model 204 Weight Indicator is a precision weight indicating instrument. As with any precision instrument, it requir

INSTALLATIONUnpackingCarefully remove indicator from shipping carton and inspect it for any damage that may have taken place during shipment. Keep ca

INSTALLATION, CONT. Battery DoorSerial I/O ThumbScrew Ground LugLoad Cell12 VDCFigure No. 2 BatteriesThe 204 indicator can use 6 "C" size Al